Table of Contents

nand_release_device - [GENERIC] release chip

nand_read_byte - [DEFAULT] read one byte from the chip

nand_write_byte - [DEFAULT] write one byte to the chip

nand_read_byte16 - [DEFAULT] read one byte endianess aware from the chip

nand_write_byte16 - [DEFAULT] write one byte endianess aware to the chip

nand_read_word - [DEFAULT] read one word from the chip

nand_write_word - [DEFAULT] write one word to the chip

nand_select_chip - [DEFAULT] control CE line

nand_write_buf - [DEFAULT] write buffer to chip

nand_read_buf - [DEFAULT] read chip data into buffer

nand_verify_buf - [DEFAULT] Verify chip data against buffer

nand_write_buf16 - [DEFAULT] write buffer to chip

nand_read_buf16 - [DEFAULT] read chip data into buffer

nand_verify_buf16 - [DEFAULT] Verify chip data against buffer

nand_block_bad - [DEFAULT] Read bad block marker from the chip

nand_default_block_markbad - [DEFAULT] mark a block bad

nand_check_wp - [GENERIC] check if the chip is write protected

nand_block_checkbad - [GENERIC] Check if a block is marked bad

nand_command - [DEFAULT] Send command to NAND device

nand_command_lp - [DEFAULT] Send command to NAND large page device

nand_get_device - [GENERIC] Get chip for selected access

nand_wait - [DEFAULT] wait until the command is done

nand_write_page - [GENERIC] write one page

nand_verify_pages - [GENERIC] verify the chip contents after a write

nand_read - [MTD Interface] MTD compability function for nand_do_read_ecc

nand_read_ecc - [MTD Interface] MTD compability function for nand_do_read_ecc

nand_do_read_ecc - [MTD Interface] Read data with ECC

nand_read_oob - [MTD Interface] NAND read out-of-band

nand_read_raw - [GENERIC] Read raw data including oob into buffer

nand_prepare_oobbuf - [GENERIC] Prepare the out of band buffer

nand_write - [MTD Interface] compability function for nand_write_ecc

nand_write_ecc - [MTD Interface] NAND write with ECC

nand_write_oob - [MTD Interface] NAND write out-of-band

nand_writev - [MTD Interface] compabilty function for nand_writev_ecc

nand_writev_ecc - [MTD Interface] write with iovec with ecc

single_erase_cmd - [GENERIC] NAND standard block erase command function

multi_erase_cmd - [GENERIC] AND specific block erase command function

nand_erase - [MTD Interface] erase block(s)

nand_erase_nand - [NAND Interface] erase block(s)

nand_sync - [MTD Interface] sync

nand_block_isbad - [MTD Interface] Check whether the block at the given offset is bad

nand_block_markbad - [MTD Interface] Mark the block at the given offset as bad

nand_suspend - [MTD Interface] Suspend the NAND flash

nand_resume - [MTD Interface] Resume the NAND flash

check_pattern - [GENERIC] check if a pattern is in the buffer

check_short_pattern - [GENERIC] check if a pattern is in the buffer

read_bbt - [GENERIC] Read the bad block table starting from page

read_abs_bbt - [GENERIC] Read the bad block table starting at a given page

read_abs_bbts - [GENERIC] Read the bad block table(s) for all chips starting at a given page

create_bbt - [GENERIC] Create a bad block table by scanning the device

search_bbt - [GENERIC] scan the device for a specific bad block table

search_read_bbts - [GENERIC] scan the device for bad block table(s)

write_bbt - [GENERIC] (Re)write the bad block table

nand_memory_bbt - [GENERIC] create a memory based bad block table

check_create - [GENERIC] create and write bbt(s) if neccecary

mark_bbt_region - [GENERIC] mark the bad block table regions

nand_update_bbt - [NAND Interface] update bad block table(s)

nand_isbad_bbt - [NAND Interface] Check if a block is bad

nand_trans_result - [GENERIC] create non-inverted ECC